MIREX EXHIBITION

a FEW FOTO I TOOK FROM MIREX EXHIBITION

DIY WATER TEMPRETURE GAUGE INSTALLATION

Diy water temperature gauge installation(DIY MEMASANG WATER TEMPRETURE METER(HOT STUFF TYPE RR)



.This meter can stick on top of your dashboard meter suhu boleh lekat dekat dashborad



fig(a)
1.. Read the manual provided or wiring diagram first before you start the work. (Baca manual atau gambarajah wairing terlebih dahalu sebelum pemasangan dilakukan)
2.. to avoid from unnecessary short circuit please remove your negative terminai batery connection
( Buka punca negative beteri kereta anda dahulu sebelum memulakan kerjaa. )



Fig(b)..
Meter Rear view( belakang meter)

3.Sambungkan wayar lampu meter ke terminal negative dan terminal positive seperti gambarajah diatas (fig(b)Connect lamp wire to terminal negative and positive meter as shown at fig( b)


fig(c)A CONNECTION HAS BEEN MADE FROM WIRE IGNITION(satu sambungan telah dibuat dari wayar ignition)
4.Remove the cover under steering car than look for ignation wire.Make a connection there(buka cover dibawah stereng stereng kereta supaya anda dapat mancari wayar ignation,buat satu sambungan disana.)

fig(d)Ground connection is made(sambungan ground sudah dibuat )
5.Connect one ground to any part of the body car.(Buat satu wayar ground,boleh disambung dimana-mana body kereta)
fig(e)
6.Just pull the wire up to dashboard through the saide of dashboard(tarik wayar sambungan tadi naik keatas dasboard melalui tepi dashboard).fig(E)

7)Slot wire into the meter holder(Masukan wayar kedalam meter holder )


fig(G)
8.Just connect the wire to terminal negative and positive meter(Sambungkan wayar tadi ke punca negative dan positive meter )

fig(h)Tempreture switch(tempreture suis )

9.Original temperature switch cant be used as the ohm value is different.I change the switch with new one supplied by distributer.( Tempreture suis standard tak boleh digunakan kerana nilai ohm adalah berbeza,tukar dengan suis yg dibekalkan oleh pengedar).10.Remove the original switch and exchange with new one(buka tempreture suis anda dan tukarkan dgn suis yang baru. )



11.Make a wire connection at the switch tempreture(buat satu sambungan wayar di suis tempreture. )


12.Pull wire switch through the passage hole of rpm cable(tarik wayar suis dan masukkan kelaluan kabel rpm supaya anda dapat menyambungka ke punca meter.)13.Wire from temperature switch is connected to the meter.Re-connect terminal negative battery to test the meter.Start the engine for a few minutes wait till it reach to a normal operation temperature and check temperature reading.Also check is there any leakage of coolant from temperature switch,if any thigten back the switch.wayar suis dari engine tadi disambung ke punca suis dimeter.sambungkan semula punca negative bateri kereta anda untuk menguji meter tempreture.hidupkan engine beberapa minit dan lihat bacaan meter.sekiranya meter beroperasi dgn baik maka kemaskan semua sambungan wiring anda dgn seelok-eloknya dan check tiada berlaku sebarang kebocoran coolant disuis tempreture anda,kalau bocor ketatkan sedikit suis tadi.14.Stick the meter to the dashboard and make sure it not interfere your vision while driving (lekatkan meter didashboard anda dan pastikan ia tidak menggangu penglihatan anda semasa memandu.....SELESAI. )



Replacing front engine mounting(DIY MENUKAR MOUNTING HADAPAN )

Newfront mounting mounting hadapan(baru).
Boken mounting
If engine mounting broken it will cause very bad engine vibration.(mounting kalau rosak akan menyebabkan engine bergegar kuat.)1.Jack the car ,placing jackstand sturdily on your left and right car.Hold the engine with jack to support engine when mounting remove from it.(dont crawl under the car with only using jack it's dengerous)Jek kereta ,letakan jak stand dgn kukuh dikiri dan kanan kereta.sokong engine dgn jek supaya engine dpt disokong apabila mounting dibuka. awas jgn masuk kebawah kereta dgn hanya menggunakan jek merbahaya.

2.Remove mounting bolt from engine bracket( buka skru mounting yg memegang breket engine. )

3.remove two mounting bolts from crossmember(Buka dua skru mounting yg memegang ke cross member) 4.to facilitate the work or to get more space ,release cross member from body chasis.Untuk memudahkan kerja atau mendapat ruang yang lebih buka dua skru cross member yang terikat di body chasis.

Remove above bolts to release cross member from chasis( buka dua bolt dibawah crossmember
5.Fix new mounting by installing the bolts to crossmember.(Pasang mounting yang baru.ikat dua skru dicross member.)

6.Instal back the mounting bolt to engine bracket(Pasang skru mounting ke breket yang memegang engine. )
7.put on 2 bolts on cross member and tighten it to body chasis securely.(Ikat semula skru di cross memeber yang melekatkan ke chasis body.selesai )
Change the termostat(MENUKAR TERMOSTAT )

Amaran jangan mengelurkan coolant,membuka tudung radiator atau menukar termostat sekiranya enjin masih panas mulakan kerja semasa enjin dalam keadaan sejuk.(warning do not remove the radiator cap,drain the coolant or replace the thermostat until the engine has cooled completely. new thermostat

1.

1.(thermostat housing terletak bersebelahan dengan cylinder head ia bersambung dengan radiator hose. thermostat housing is located just next to cylinder head and radiator hose connect to it).

(2. )

2.(slacken the clip and detach the coolant hose from the thermostat housing cover be prepare coolant will splash out )Buka skru clip di radiator hose ,tarik hose supaya ia keluar dari housing, coolant akan keluar dari hose ,sediakan besin dibawahnya supaya dapat menakung coolant.

(3a)


3a)(unscrew the securing bolt)buka dua skru di housing termostat
3b
3b)Thermostat sudah dikeluarkan ,bersihkan sisa gasket atau rtv yang masih melekat.(remove thermostat and clean all trace of the old gasket and rtv which stick at housing area)
(3c)


3c)bersihkan sisa gasket dan juga gam rtv yang melekat di tudung termostat(clean old gasket and rtv from thermostat cover

3.Buka 2 skru housing supaya tudung termostat boleh dibuka ,sekiranya ketat cuba ketuk dgn tukul getah sehingga ia terbuka,cabut tudung dan keluarkan gasketnya sekali.(Unscrew the two bolt and remove the cover from the termostat housing.if it stick tap it gentaly with a soft mallet,remove the gasket,then lift the thermostat from the housing)



(4) Masukan termostat baru ketempat asalnya semula.Kedudukan termostat mestilah betul iaitu spring menghala kebawah.(Fit new thermostat squarely into its housing obsereving the correct orientation -compressing spring must face down)


(5)Pasang gasket baru diatas termostat housing,pasang termostat cover dan ikat semula dua skru sheinga ketat secukupnya.(Lay new gasket in position over the thermostat housing cover in position,then insert the retaining bolt and thigten it.)
(6)Pasang semula coolant hose dan ketatkan clipnya.(Refit the coolant hose and thighten the hose clip securerly


Refill the coolent sufficiently to the radiator tank) (7)Tambahkan coolant ke dalam radiotor sehingga cukup.(
(8)Hidupkan engine dan pastikan sistem penyejukan beroperasi dengan baik.(Start the engine and check the cooling system is working properly)

diypomen facebook

PERINGATAN.

Kerja -kerja DIY adalah tanggungjawab anda sendiri ,saya tidak bertanggungjawab atas kecederaan diri atau kerosakan kenderaan yang berlaku kepada anda.patuhi peraturan dan keselamatan semasa melakukan kerja.Rujuk kepada peraturan dan keselamatan semasa berkerja di bengkel kereta..contoh 1)kerja yang berkaitan dengan petrol boleh melibatkan kebakaran..2.Menjek kereta amat merbahaya sekiranya tidak mengikut peraturan kerana jek boleh rosak pada bila-bila masa dan kerata akan jatuh..3.) habuk break sangat merbahaya jika tehidu dan macam-macam lagi..so utamakan keselamatan anda terlebih dahulu..

diy memasang projector head lamp(diy install head lamp projector)

nampak kemas dan mantap tapi kereta dah cabok (look cool with projector)
head lamp ni lampu warna kuning tak silau sangat(using normal bulb only the light not so sharps)1.Buka bonet kereta cari lokasi head lamp (find headlamp location) 2.Buka dua skru dibelakang head lamp,gunaka soket 10mm (unscrew the two bolt behind headlamp)
spring retainer untuk memegang signal lamp (spring retainer to hold the signal lamp)
signal lamp sudah dilonggarkan dari breketnya (signal lamp loosed from it brackets)
3.tarik spring sehingga signal lamp tercabut.(pull the spring retainer until it release the signal)4.cabut 2 wayar konektor.5.buka dua skru di sisi head lamp.tarik keluar head lamp.
6.masukan new head lamp.pasang semula skru belakang dan skru sisi.pasang signal semula.sambung wayar connector semula.check samada mentol menyala...selesai

diypomen facebook

Engine oil and filter change.(diy menukar minyak engine)

Oil sump is a place to keep an engine oil( oil sum tempat minyimpan minyak hitam)Used jack stand to support your car( jeck stand menyokong kereta dengan selamat )
1.Jack front car until you can see an oil sump location.Support car with jack stand securely.If you dont have this equipment please dont continue this procedure ,it dangerous and can harm you,please refer how to jack the car with the correct and safety way.(Jek kereta sehinga anda dapat melihat oil sum.sokong kereta anda dengan jeck stand sehingga kukuh dan selamat barulah anda boleh memulakan kerja sekiranya anda tidak mempunyai jek stand atau tidak mahir menggunakan jeck jangan teruskan kerja ini kerana ia boleh membahayakan anda..rujuk dahulu cara yang betul dan selamat bagaimana mengunakan jeck kereta .. )
2.Use a wrench to remove the nut and allow the oil drain in to the pan.Makesure the pan is big enough to support the volume of oil.buka skru dan biarakan minyak mengalir sehingga kering ke dalam besin ,pastikan besin cukup untuk menakung minyak

slacken the oil filter( buka penapis minyak)oil filter already remove from engine( penapis minyak sudah dibuka )
3Use an oil filter wrench to slacken the filter ,prepare container for oil to drainage.(bukan oil filter dengan menggunakan oil filter remover,pastikan anda letakkan besin dibawahnya kerana minyak akan mengalir keluar biarakan minyak mengalir keluar sehingga kering.)
4.Applay a light coating of clean engine oil to the sealing ring on the new filter then screw the filter in to position on the engine.Tighten the filter firmly by hand only-do not use any tools.(Pasang oil filter baru.sapukan sedikit minyak engine diatas gaskit getah di oil filter kemudian pasang oil filter semula ketatkan dengan mengunakan tangan saja kerana sekiranya menggunakan spana takut akan merosakkan gasketnya dan kebocoran minyak boleh berlaku.) Filler hole ,where you pour an engine oil(TEMPAT MENGISI MINYAK ENGINE)The correct engine oil volume is in betwen min and max from the oil dipstick indicator or 3/4 to the max level.( ukuran minyak adalah diantara penanda min dan max atau 3/4 menghampiri tanda max. )5.Tighten back the nut from the oil dranage sump.Release the jack to lower the vehicle to the ground.Fill the engine oil through the filler hole until to the optimum level.Tighten oil filler cap,start the engine for a few minutes and checking for leaks around the oil filter seal and the sump drain plug.Stop the engine and wait a few minutes recheck the level on the dipstick and add more oil as necessary(Ketatkan skru oil drainage dibawah oil sum.turunkan jek dan isikan minyak engine baru sehingga had yang mencukupi.tahap minyak engine boleh diukur dengan oil dipstick. Tutup oil filler cap.hidupkan engine beberapa minit kemudian chek tahap minyak engine sekali lagi sekiranya kurang tambah minyak sehinga cukup.chek sekali lagi di skru oil sum dan oil filter kalau ada berlaku kebocoran sekiranya ada ketatkan skru yang berkenaan..selesai )

diypomen facebook