Membuka dan memasang sport stereng,(REMOVE AND INSTALL SPORT STEARING)

Membuka(To Remove stearing)

Sebelum membuka stereng,pastikan roda anda berada dalam kedudukan yg lurus(.Before removing the steering wheel, make sure that your wheel is in the stright position.)

1.Buka semua elen skru sehingga stering terbuka.(To remove stearing from the hub you need to lossen  all the allen screw)

2.untuk melepaskan stereng dari horn,terlebih dahulu buka wayaring di bahagian horn

.(To release the stearing from the horn,firstly you need to release the horn wiring)

cabut wayar dari horn(Pull wire from the horN)

3.Stereng sudah dibuka dari hubnyaStereng hub.(Stearing is removed from the steering hub.)

stearing hub

Memasang(Installing)

1.masukan wayar horn dicelah lubang stereng dan sambungkan terus ke horn.(Insert the wire through the stearing whole and connect directly to the horn)

2.pasangkan stereng cover dan pasang semua skru,ketatkan skru secukupnya (install the steering wheel cover and  tighten all the screws securely.)

3.Test horn anda…selesai (test the horn ...completed)

DIY MEMBUKA DAN MEMASANG MENTOL HADAPAN PROJECTOR HEAD LAMP(REMOVE AND REPLACING BULB FROM PROJECTOR HEAD LAMP)

1. Mentol depan belah kiri dah terbakar sebulan tak sempat nak tukar.Petang ni den ado masa nak tokar.Projector lamp ni susah sikit nak buka dia tak sama dengan head lamp biasa maklumlah dia banyak mentol,tapi tak lah sesusah mana kalau kita sabar sikit..ok kita mula sekarang..(my projector head lamp was burned so its time to do diy again.

Peralatan(Tools needed)

Tangan dengan screw driver aje(screwdriver)

1.Buka breket Rellay dahulu kerana ia menghalang mentol dari ditarik keluar.(open rellay bracket first cause it blocking our hand from pulling the rubber cover out.)

kotak rellay(Rellay box)

buka skru(remove screw)


buka skru(remove screw)


2.Tarik keluar cover getah dari head lamp(Pull out the rubber cover from head lamp.)


Tarik cover getah keluar(Pull out the rubber cover)

cover dah dibuka(removed cover)

3.Cabut wayar mentol(pull the wiring connection from the bulb)

CARA PEMASANGAN RADIO player KERETA ( car stereo instalation)

keselamatan(safety)

Before performing any task involving electrical components in your vehicle,make sure to first disconnect the negative battery terminal cable.If you bypass this step you run the risk of creating a short in the system,damaging the components and wiring of your vehicle.(Sebelum memulakan penyambungan wayar buka kabel negative bateri dahulu,tujuanya adalah untuk mengelakan berlakunya kejadian litar pintas semasa penyambungan wayar sedang dilakukan.)


peralatan.(tool)
=elekterik tape(electrical tape)

=pemotong wayar(wire cutter)

.after understanding entire audio wiring track in your car,then you can persued installation work,if you uncertain do not continue because of errors in wiring cause damaging your stereo.Setelah memahami keseluruhan litar radio yang baru dan litar audio dari kereta anda,maka bolehlah kerja pemasangan boleh diteruskan.Sekiranya anda tidak pasti atau was-was sebaiknya jangan diteruskan kerana penyambungan yang salah akan merosakkan radio anda



Pull out you factory stereo,remove wire entena,speaker and power supply.(cabut radio lama anda dari tempatnya ,cabut wayar entena,wayar speker dan wayar power supply.)




radio dah dicabut,wiring radio dan entena, (audio wiring from the car)
sambung wayar radio baru ke adapter wiring kereta. (connect new wiring stereo to the correct wiring from the car)


wiring bateri,ground dan accesory(wiring battery,ground and accesory)

Pivot Raizin volt stabilizer installation(memasang pivot raizin volt stabilizer)

Warning ==install safely and surely by following these instruction,please be very careful about connecting the positive and negative cables,mixing these up will cause damage to the product. "amaran"hati-hati semasa pemasangan alat ini ke terminal positive dan terminal negative,kesilapan penyambungan keterminal boleh merosakkan alat ini.




1.Remove the negative cable from negative terminal battery.Mula -mula buka cable di negative bateri kereta.

2.Connect positive raizin cable to the positive battery terminal and tighten the nut securely.Sambungkan cable positive raizin ke terminal positive bateri,ketatkan skru secukupnya.
3.Properly connect the negative cable to the negative battery.connect the negative cable raizin to the terminal

carefully when driving with spare tyre(berhati-hati memandu semasa menggunakan tayar spare)

-Spare tyre only can used for temporary and emegency purpose .This tyre cannot be used for daily drive,it dangerous.(Spare tayar hanya boleh digunakan untuk sementara waktu sahaja)

-Read the instruction how to used this spare tyre,it can be found from car manual book or it stated at the rear bonnet near the spare tyre.(Baca peraturan menggunakan tayar spaire,ada tercatat di manual book atau tertulis dibonet belakang berhampiran tayar.)

Proton akan menghasilkan engine campro turbo/proton will release new turbo engine campro.

Now people busy talking about proton will produce new engine campro turbo .my neighbour work at proton give me some information about this engine.He told me that r&d department now are busy testing of this engine extensively.Modified has been done to the engine so it can accept high pressure from the turbo exzos.At the engine block ,the diameter of water jacket changed to a bigger size so it can improve cooling system more efficient.Possibility this engine will be install to proton exora mpv.. Sekarang ni. tengah heboh orang bercerita pasal proton nak pakai engine turbo.Jiran saya kerja kat proton bagi information sikit dia kata r & d tengah sebok test engine ni.pengubahsuian perlu dilakukan keatas engine supaya dapat menahan tekanan yang dihasilkan dari turbin exzos.Lubang water jacket di engine blok juga sudah dibesarkan supaya dapat menyejukkan engine dengan lebih efficent.engine turbo ni katanya nak disumbat kat mpv exora tu.

spesifikasi engine
1.6 liter campro turbo/cps turbo engine =150 horsepower

Kisah pencipta lampu

.Salam Bro post kali saja nak post satu fakta tentang seorang saintis ni =Thomas Edison adalah saintis pertama yang mencipta cara menghasilkan cahaya melalui tenaga elektrik.Apa yang menarik adalah beliau menemui 999 cara salah dan satu cara yang betu bagi mencipta sebuah mentol.Ini adalah sikap positif yang perlu bagi setiap orang.Sekali gagal tidak selamanya gagal..so rajin-rajin lah berusaha dan jangan kenal putus asa..

REMOVE AND ISNTALLATION OF RADIATOR FAN.(MEMBUKA DAN MEMASANG KIPAS RADIATOR)

Last friday when i was driving to Sunway Pyrimid suddenly my engine tempreture meter reach to 120celcius ,quickly i stop my car check the engine and found radiator fan not spinning.I was lucky because my engine didn't overheat yet,but i can heard boiling sound came out from radiator.After rest for half an hour i continue drive to look for workshop unfortunetly all workshop was closed,so i have no choices,i have to sattle this problem alone with myself.First thing i do is check fuse and its ok then i do direct connection fan to battery and found fan not spinning so i cant do anything more...my solution is wait until night when the road is free i drive slowly and safetly back to my home.( Hari Jumaat lepas semasa nak pergi sunway pyramid tiba-tiba tengok meter tempreture dah sampai 120celcius ,mak oi problem ni bawak budak kecik pulak nih,selepas tol saya berhenti buka bonet tengok kipas radiator dah kong.engine panas ,dekat radiator boleh dengar air mengelegak ,nasib baik air tak memancut keluar(pakai penutup radiator japan ,tahan lasak penutup radiator ni tahan dengan high pressure).Saya lepak setengah jam pas tu pandu terus masuk pyramid ,bengkel semua dah tutup masak aku kali ni.Anak ngan maknya suruh lepak kat pyramid saya cuba nak setelkan kipas ni tension tul.Perkara pertama check fius ok,pas tu buat direct connection betri ke kipas ,tak jalan juga maka betoi lah kipas ni dah ko.(Bro nak buat direct kipas pusing mesti hati-hati OK,PANASSS,KIPAS BOLEH PUSING TIBA-TIBA JAGA JARI DGN TANGAN ANDA).sO saya tak boleh nak buat apa-apa tungu malam sikit jalan clear baru saya gerak,pahem-pahem lah SUN WAY TOL jEm tahap gile,kalau gua lalu time jEm masti kantoi kereta ni.pukul 8 malam saya gerak ,selamat sampai kerumah,ambik masa satu jam..)

1.before starting your work makesure the engine is not hot.(Sebelum memulakan kerja pastikan engine kereta anda tidak panas.)


2.Remove all bolt that hold the radiator fan(Buka keempat-empat bolt yang memegang kipas radiator.)

3 POINTS ULTRA RACING REAR BAR INSTALLATION FOR PROTON GEN2,PERSONA AND WAJA(MEMASANG 3 POINTS BAR BELAKANG PROTON GEN 2,PERSONA DAN WAJA)

3 POINTS REAR BAR

1.Remove all nuts from both suspension(BUKU DUA NUT ABSORBER ,KIRI DAN KANAN.)


2.Fix the bar to the suspension ,put on the nuts back but done tighten it first.(PASANG KAN BAR DI TEMPAT YANG SEPATUTNYA,PASANG SEMULA NUT ABSORBER,TAPI JANGAN DIKETATKAN NUT TERSEBUT DAHALU.)

DIY REPLACE ROCKER COVER GASKET(diy menukar rocker cover gasket)

1. Before you remove the rocker cover you must pull out two hose that attached to it.Loosen all the bolt and remove the cover,if it stuck use rubber hammer and hit at the edges of cover slowly until it loose.(sebelum membuka rocker cover, paip crancase dan brether paip hendalah dibuka terlebih dahulu kemudian Buka skrew rocker cover,ada enam kesemuanya.buka rocker cover ,sekiranya ketat ketuk disisi cover degan tukul getah perlahan-lahan sehinga ia longgar.)




2.Rocker cover has been removed out from the head.Used scraper to Clean all trace and old gasket that stick to head and cover area(Rocker cover sudah dibuka,bersihkan segala kotoran atau gasket lama yang melekat dikawasa head dan dikawasan rocker cover.)

Fuel pump(carbureted model)-removel and instalation (diy membuka dam memasang mekanikal petrol pam)

1.This pump is leaked it caused oil from engine head dirty the belt and compressor air con.(pam minyak ni dah bocor ,minyak hitam dari head dah keluar mengotorkan belting dan compressor aicond.)

All hoses removed from pump.(paiping di pam minyak dah dibuka.)

.TURBO TIMER INSTALLATION /DIY MEMASANG TURBO TIMER.

turbo timer

1.Read first the instruction given by the manufacturer before you installing this gadget.
a)Red=forever positive
b)Yellow=for key switch second positive=electronic assay
c)blue=key switch engine
d)black=negative
e)brown=hand brea
Sebelum memasang baca dahalu arahan yang yang dibekalkan oleh pengilang merah=wiring terus dari punca positive beteri(red =forever positive)
kuning=wiring kunci eksesori(yellow=for key switch second positive=electronic assay)biru=wiring kunci engine(blue=key switch engine)
hitam/black =negativebrown/perang=hand brake
switch cover has been remove(switch cover sudah dibuka) test lamp

2.Remove switch cover so you can make a wire connection more easy.Here i was stucked because i dont have a car wiring diagram but dont worry we can use the test lamp to help us to identify them.Mark all the identified wire.( buka cover switch supaya anda dapat membuat sambungan wayar disitu.kat sini saya dah stuck tak ada gambarajah wiring kereta , jangan risau kita boleh gunakan test lamp untuk mengecam setiap satu wayar tersebut.)
aligator clip(aligator klip )



PERHATIAN=



Kalau boleh semasa mengesan wayar gunakan voltmeter test(,alat ini boleh dibeli kat hardware harganya sekitar rm20 ke rm40) kerana alat ni arusnya tak sekuat arus dari test lamp.Jangan gunakan test lamp untuk menguji peralatan elektronik kereta anda kerana arus dari mentol test lamp kadang-kadang boleh melebihi 12volt dan akan merosakan peralatan elektronik yang berhampiran.BRO SAYA GUNAKAN ALAT NI SEBAB IA MUDAH UNTUK SAYA ,LAGI PUN KERETA SAYA TAK DE ECM (COMPUTER BOX),TAPI KALAU UNTUK NEW BEGINER SEBAIKNYA GUNALAH VOLT METER.




3.How to use the test lamp=alligator clip can be connect to anypart of car body,the needle is injected in to the wire for identify.Turn the switch on one by one and identify them.Mark all the identified wire.cara menggunakan test lamp=aligator klip boleh disambung dimana -mana body kereta,bahagian jarum dicucuk ke dalam wayar yang hendak dikesan.putar kunci switch satu persatu dan test wayar.(BILA MENTOL MENYALA TERUS CABUT TEST LAMP DARI WAYAR,KALAU MENTOL MENYALA TERLALU LAMA ,ARUS DARI MENTOL BOLEH MENGALIR KE PERALATAN ELEKTRONIK YANG BERHAMPIRAN DAN BERKEMUNGKINAN MEROSAKANNYA.)tandakan wayar yg telah dikenal pasti satu persatu.

4.Before starting your work please open negative battery source first .This is to avoid any short circuit occurrence.(sebelum memulakan penyambungan buka punca negative bateri terlabih dahulu untuk mengelakan sebarang kejadian litar pintas.) 5.Open the switch connector so connection task is more easy to do(buka conector suis supaya anda mudah membuat sambungan.) 6.One of the wire from adaptor is connected to another wire from switch.All togather is three wire ,connect them one by one and tape the connection with electrical tape securely.(adaptor dari turbo timer sedang disambung dgn salah satu wire suis,semuanya ada tiga wayar.so selesaikan semuanya dan tapekan sambungan sekemas-kemasnya.0

7.connect the adaptor to turbo timer and connect back the wiring switch(sambungan adaptor tadi ke turbo timer dan sambung semula conector ke punca suis.)

hand break switch(suis hand break )

make one connection to hand break switch(buat sambungan disuis hand break )


tape wire securely,if can solder it.(tape wayar kemas-kemas kalau boleh shoulder. )

8.Remove hand break cover and make connection at the hand break switch.If you skip this the timer still can work.Many people skip this procedure but for saftey purpose is batter for you to do the connection.(buka cover hand break dan buat sambungan di suis hand break,kalau tak sambung pun timer boleh berfungsi tapi untuk saftey baik sambung bukan susah pun. )

9.Last step is connect negative wire to car body(.akhir sekali sambungkan wayar negative kemana -mana body.)

10.Re-connect the negative battery source and set turbo timmer according to engine type or the timer you like to hold.(sambungkan negative bateri semula dan set turbo timer mengikut kesukaan anda.selesai )

diypomen facebook

JASMA LIGHTWEIGHT RACING CRANK PULLEY

fetures

• light weight



• made by billet aluminium



• more horsepower and torque
  
• quicker throttle respone
  
• just plug and play no maintanance needed
  
• save petrol
  
  
  
  

diypomen facebook

012-9720635

MIREX EXHIBITION

a FEW FOTO I TOOK FROM MIREX EXHIBITION

DIY WATER TEMPRETURE GAUGE INSTALLATION

Diy water temperature gauge installation(DIY MEMASANG WATER TEMPRETURE METER(HOT STUFF TYPE RR)



.This meter can stick on top of your dashboard meter suhu boleh lekat dekat dashborad



fig(a)
1.. Read the manual provided or wiring diagram first before you start the work. (Baca manual atau gambarajah wairing terlebih dahalu sebelum pemasangan dilakukan)
2.. to avoid from unnecessary short circuit please remove your negative terminai batery connection
( Buka punca negative beteri kereta anda dahulu sebelum memulakan kerjaa. )



Fig(b)..
Meter Rear view( belakang meter)

3.Sambungkan wayar lampu meter ke terminal negative dan terminal positive seperti gambarajah diatas (fig(b)Connect lamp wire to terminal negative and positive meter as shown at fig( b)


fig(c)A CONNECTION HAS BEEN MADE FROM WIRE IGNITION(satu sambungan telah dibuat dari wayar ignition)
4.Remove the cover under steering car than look for ignation wire.Make a connection there(buka cover dibawah stereng stereng kereta supaya anda dapat mancari wayar ignation,buat satu sambungan disana.)

fig(d)Ground connection is made(sambungan ground sudah dibuat )
5.Connect one ground to any part of the body car.(Buat satu wayar ground,boleh disambung dimana-mana body kereta)
fig(e)
6.Just pull the wire up to dashboard through the saide of dashboard(tarik wayar sambungan tadi naik keatas dasboard melalui tepi dashboard).fig(E)

7)Slot wire into the meter holder(Masukan wayar kedalam meter holder )


fig(G)
8.Just connect the wire to terminal negative and positive meter(Sambungkan wayar tadi ke punca negative dan positive meter )

fig(h)Tempreture switch(tempreture suis )

9.Original temperature switch cant be used as the ohm value is different.I change the switch with new one supplied by distributer.( Tempreture suis standard tak boleh digunakan kerana nilai ohm adalah berbeza,tukar dengan suis yg dibekalkan oleh pengedar).10.Remove the original switch and exchange with new one(buka tempreture suis anda dan tukarkan dgn suis yang baru. )



11.Make a wire connection at the switch tempreture(buat satu sambungan wayar di suis tempreture. )


12.Pull wire switch through the passage hole of rpm cable(tarik wayar suis dan masukkan kelaluan kabel rpm supaya anda dapat menyambungka ke punca meter.)13.Wire from temperature switch is connected to the meter.Re-connect terminal negative battery to test the meter.Start the engine for a few minutes wait till it reach to a normal operation temperature and check temperature reading.Also check is there any leakage of coolant from temperature switch,if any thigten back the switch.wayar suis dari engine tadi disambung ke punca suis dimeter.sambungkan semula punca negative bateri kereta anda untuk menguji meter tempreture.hidupkan engine beberapa minit dan lihat bacaan meter.sekiranya meter beroperasi dgn baik maka kemaskan semua sambungan wiring anda dgn seelok-eloknya dan check tiada berlaku sebarang kebocoran coolant disuis tempreture anda,kalau bocor ketatkan sedikit suis tadi.14.Stick the meter to the dashboard and make sure it not interfere your vision while driving (lekatkan meter didashboard anda dan pastikan ia tidak menggangu penglihatan anda semasa memandu.....SELESAI. )



Replacing front engine mounting(DIY MENUKAR MOUNTING HADAPAN )

Newfront mounting mounting hadapan(baru).
Boken mounting
If engine mounting broken it will cause very bad engine vibration.(mounting kalau rosak akan menyebabkan engine bergegar kuat.)1.Jack the car ,placing jackstand sturdily on your left and right car.Hold the engine with jack to support engine when mounting remove from it.(dont crawl under the car with only using jack it's dengerous)Jek kereta ,letakan jak stand dgn kukuh dikiri dan kanan kereta.sokong engine dgn jek supaya engine dpt disokong apabila mounting dibuka. awas jgn masuk kebawah kereta dgn hanya menggunakan jek merbahaya.

2.Remove mounting bolt from engine bracket( buka skru mounting yg memegang breket engine. )

3.remove two mounting bolts from crossmember(Buka dua skru mounting yg memegang ke cross member) 4.to facilitate the work or to get more space ,release cross member from body chasis.Untuk memudahkan kerja atau mendapat ruang yang lebih buka dua skru cross member yang terikat di body chasis.

Remove above bolts to release cross member from chasis( buka dua bolt dibawah crossmember
5.Fix new mounting by installing the bolts to crossmember.(Pasang mounting yang baru.ikat dua skru dicross member.)

6.Instal back the mounting bolt to engine bracket(Pasang skru mounting ke breket yang memegang engine. )
7.put on 2 bolts on cross member and tighten it to body chasis securely.(Ikat semula skru di cross memeber yang melekatkan ke chasis body.selesai )
Change the termostat(MENUKAR TERMOSTAT )

Amaran jangan mengelurkan coolant,membuka tudung radiator atau menukar termostat sekiranya enjin masih panas mulakan kerja semasa enjin dalam keadaan sejuk.(warning do not remove the radiator cap,drain the coolant or replace the thermostat until the engine has cooled completely. new thermostat

1.

1.(thermostat housing terletak bersebelahan dengan cylinder head ia bersambung dengan radiator hose. thermostat housing is located just next to cylinder head and radiator hose connect to it).

(2. )

2.(slacken the clip and detach the coolant hose from the thermostat housing cover be prepare coolant will splash out )Buka skru clip di radiator hose ,tarik hose supaya ia keluar dari housing, coolant akan keluar dari hose ,sediakan besin dibawahnya supaya dapat menakung coolant.

(3a)


3a)(unscrew the securing bolt)buka dua skru di housing termostat
3b
3b)Thermostat sudah dikeluarkan ,bersihkan sisa gasket atau rtv yang masih melekat.(remove thermostat and clean all trace of the old gasket and rtv which stick at housing area)
(3c)


3c)bersihkan sisa gasket dan juga gam rtv yang melekat di tudung termostat(clean old gasket and rtv from thermostat cover

3.Buka 2 skru housing supaya tudung termostat boleh dibuka ,sekiranya ketat cuba ketuk dgn tukul getah sehingga ia terbuka,cabut tudung dan keluarkan gasketnya sekali.(Unscrew the two bolt and remove the cover from the termostat housing.if it stick tap it gentaly with a soft mallet,remove the gasket,then lift the thermostat from the housing)



(4) Masukan termostat baru ketempat asalnya semula.Kedudukan termostat mestilah betul iaitu spring menghala kebawah.(Fit new thermostat squarely into its housing obsereving the correct orientation -compressing spring must face down)


(5)Pasang gasket baru diatas termostat housing,pasang termostat cover dan ikat semula dua skru sheinga ketat secukupnya.(Lay new gasket in position over the thermostat housing cover in position,then insert the retaining bolt and thigten it.)
(6)Pasang semula coolant hose dan ketatkan clipnya.(Refit the coolant hose and thighten the hose clip securerly


Refill the coolent sufficiently to the radiator tank) (7)Tambahkan coolant ke dalam radiotor sehingga cukup.(
(8)Hidupkan engine dan pastikan sistem penyejukan beroperasi dengan baik.(Start the engine and check the cooling system is working properly)

diypomen facebook